linus

我的计算机启动后出现蓝屏，错误信息如下，请问哪位知道如何解决？

***STOP: 0x000000A5 (0x00000001, 0x816B4228, 0x00000000, 0x00000000)***

The ACPI BIOS in this system is not fully compliant with the ACPI secification.
Please read the README.TXT for possible workarounds. You can also contact your
system's manufacturer for an updated BIOS, or visit http://www.hardware-update.com
to see if a new BIOS is available.

The BIOS in this system is not fully ACPI compliant. Please contact your system
vendor or visit http://www.hardware-update.com for an updated BIOS. If you are
unable to obtain an updated BIOS or the latest BIOS supplied by your vendor is
not ACPI compliant, you can turn off ACPI mode during text mode setup. To do this,
simply press F7 key when you are prompted to install storage drivers. The system
will not notify you that the F7 key was pressed, it will silently disable ACPI
and allow you to continue your installation.

autoday

解决了吗?如果没有请留下你的电话.

Lauren

Have you changed your hardware lately? or, check the memory, my friend had almost the same problem, and found the memory was damaged in the end.

linus

现在倒是操作系统能运行了。我是把所有板卡全部重插了一遍，可是系统好像不太稳定，有时还是会出现蓝屏，这是就要一块一块减掉，待系统稳定后再加上。真是繁。

WangYcca

进入cmos设置，把ACPI给diable了就行了。

我在我机器超频时间过这种状况。你超频否？

linus

How to disable ACPI in CMOS? Which field should I set? I only find "ACPI Suspend Type" field in "ower Management" section, which has 2 values: "owerOn Suspend" and "Suspend to RAM".
Thanks.

WangYcca

就在电源管理里边。

STR是从内存唤醒

linus

WangYcca,请指教是下面哪个field. Thanks.

4.8. POWER MANAGEMENT SETUP
Figure 4.5: Power Management Setup
R These two items will show up when “Resume by Alarm” is Enabled.
· Power Management
The default value is Enabled.
Enabled Enable Green function.
Disabled Disable Green function.
BIOS Configuration
4-19
· PM Control by APM
The default value is Yes.
Yes Enable software APM function.
No Disable software APM function.
· Video off Method
The default value is DPMS.
V/H SYNC + Blank BIOS will turn off V/H-SYNC when gets into
Green mode for Green monitor power saving.
Blank Screen BIOS will only black monitor when gets into
Green mode.
DPMS BIOS will use DPMS Standard to control VGA
card. (The Green type VGA card will turn of
V/H-SYNC automatically.)
· Suspend Mode
The default value is Disabled.
Disabled Disable Suspend Mode.
1 min - 1
Hour
Setup the timer to enter Suspend Mode.
· HDD Power Down
The default value is Disabled.
Disable Disable HDD Power Down mode function.
1-15 mins. Enable HDD Power Down mode between 1 to 15 mins.
· VGA Active Monitor
The default value is Disabled.
Disabled Disable monitor VGA activity.
Enabled Enable monitor VGA activity.
BX2000
4-20
· Soft-off by PWR-BTTN
The default value is Instant-Off.
Instant-off Soft switch ON/OFF for POWER ON/OFF
Delay 4 Sec. Soft switch ON 4sec. for POWER OFF.
· System After AC Back
The default value is Soft-Off.
Memory This function depends on computer status
Soft-Off Set System Soft-Off Status.
Full-On Set System Full-On Status.
· Power LED in Suspend
The default value is BLINKING.
BLINKING Set Power LED in Suspend at BLINKING mode.
ON Set Power LED in Suspend at ON mode.
OFF/DUAL Set Power LED in Suspend at OFF/DUAL mode.
· CPUFAN Off In Suspend
The default value is Enabled.
Disabled Disable this function.
Enabled Stop CPU FAN when entering Suspend mode.
· PME Event Wakeup
The default value is Enabled.
Disabled Disable PME Event Wakeup.
Enabled Enable PME Event Wakeup.
BIOS Configuration
4-21
· ModemRingOn / WakeOnLan
The default value is Enabled.
Disabled Disable these functions.
Enabled Enable these functions.
· ACPI Suspend Type
The default value is Power On Suspend.
Power On
Suspend
Set ACPI Suspend Type is Power On Suspend.
Suspend to
RAM
Set ACPI Suspend Type is Suspend to RAM.
· Resume by Alarm
The default value is Disabled.
Disabled Disable this function.
Enabled Enable alarm function to POWER ON system.
If the “Resume by Alarm” is Enabled.
Date ( of Month) Alarm : 0~31
Time ( hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)
· IRQ [3-7,9-15] , NMI
The default value is Enabled.
Disabled Disable this function.
Enabled Enable monitor IRQ [3-7,9-15] for Green event.
· Primary IDE 0/1
The default value is Disabled.
Disabled Disable this function.
Enabled Enable monitor Primary IDE 0/1 for Green event.
· Secondary IDE 0/1
BX2000
The default value is Disabled.
Disabled Disable this function.
Enabled Enable monitor Secondary IDE 0/1 for Green event.
· Floppy Disk
The default value is Enabled.
Disabled Disable this function.
Enabled Enable monitor Floppy Disk for Green event.
· Serial Port
The default value is Enabled.
Disabled Disable this function.
Enabled Enable monitor Serial Port for Green event.
· Parallel Port
The default value is Disabled.
Disabled Disable this function.
Enabled Enable monitor Parallel Port for Green event.

micky_piggy

information from Microsoft

winxp  win2k

linus

Thanks a lot. Very useful information.